E-Tech ET8 Installationshandbuch PDF herunterladen (Seite 54)

E-TECH RADIO

E-TECH ET8 (V4) CONTROL PANEL – INSTALLER MANUAL

RADIO QUICK START

PROGRAMMING RADIO KEYS:



Select which User Codes 2–8 will be Radio Codes (P09E–P10E)



Select the User Code (P12E–P25E)



Press 1E

The READY light will turn ON to indicate that the User Code is ready to accept the Radio Key



Press the OFF button on the Radio Key to be programmed

If the Radio Key is accepted, the READY light will turn off and 3 beeps will sound

PROGRAMMING RADIO DEVICES (Radio PIRs etc):



Select a zone to which the Radio PIR will be assigned (P01E–P08E)



Press 1E

The READY light will turn ON to indicate that the zone is ready to accept the Radio Device.



Trigger the Radio Device

If the Radio Device is accepted, the READY light will turn off, the ARMED light will turn on and 3 beeps

will sound.

E-TECH RADIO INTERFACE

The E-Tech Radio Interface (100–200) is the optional radio receiver required to enable all

radio functions. Connection to the control panel is via a 4 wire loom and plug supplied with

the E-Tech Radio Interface.

If the E-Tech Radio Interface is correctly installed, the ET8 keypad will flash the RADIO

light ON when any radio signal is detected (from both programmed and non-

programmed radio devices).

+12VRED

RECEIVER

DATA

WHITE

RSSIBLUE

OVBLACK

E-TECH RADIO INTERFACE

Part No. 100–200

E-TECH ET8

CONTROL PANEL

SIGNAL STRENGTH

The Signal Strength test can be used to test the radio signal from any E-Tech

radio device. The strength of the radio signal received is displayed on the zone

lights 1~8 and beeped by the keypad.

The higher the number displayed (and beeped) the stronger the signal

received.

TEST SEQUENCE:



Enter the option for the radio device to be tested

For Radio Keys: options P12E~P25E. For all other radio devices: options P01E~P08E



Press 3E



Trigger the radio device

• One of zone lights 1~8 will turn ON to indicate the signal strength from the transmitter

• The Signal Strength display remains on until another command is entered

• To clear the display and re-test the transmitter, simply press 3E again (or 4E to test any other transmitter)

NOTES:

• The E-Tech Radio Interface is normally

installed inside the control panel box.

• In cases where radio reception needs to

be improved, the Radio Interface can be

installed up to 50 metres away from the

control panel. (Use 14/0.20 cable)

• If the Radio Interface must be installed

inside a metal enclosure, the antenna

wire should protrude outside the

enclosure.

• For best performance, the antenna wire

should not be kept straight and not

coiled, shortened or extended.

NOTES:

• Signal strength of Radio Keys can be

tested in USER PROGRAM Mode or

INSTALLER PROGRAM Mode.

• Signal strength of all other Radio Devices

is tested in INSTALLER PROGRAM Mode.

• PRESS 3E to test the signal strength of

the selected transmitter ONLY. (Other

devices will be ignored).

• PRESS 4E to test the signal strength of

ANY E-Tech transmitter (including

unprogrammed devices).

WEAK

SIGNAL

(1 beep)

BEST

SIGNAL

(8 beeps)

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 63 64

Kommentare zu diesen Handbüchern

Keine Kommentare

E-Tech ET8 Installationshandbuch Seite 54

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme E-Tech ET8